a division of Masonry Supply, Inc.
156 Piper Road
Covington, Georgia 30015
MATERIAL SAFETY DATA SHEET
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
H.B. Fuller Company
3530 Lexington Avenue N
St. Paul, MN 55126-8976
Product Name& Number: PD-O725-P
Trade Name: FULATEX POLYMER --MS-ACRYLIC is Fulatex Polymer
Product Description (product use): Resin Emulsion in water
SECTION 2: COMPOSITION INFORMATION ON INGREDIENTS
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace
Hazardous Materials Information System (WHMIS). Unlisted ingredients are not hazardous per the OSHA standard and/or are not found on the WHMIS ingredient disclosure list.
See Section 16 for additional information.
SECTION 3: HAZARDS IDENTIFICATION EMERGENCY OVERVIEW
No specific warnings for normal use conditions.
POTENTIAL HEALTH EFFECTS
Eyes; Eye contact with liquid product may cause irritation.
Skin: Prolonged or repeated contact with liquid product may cause irritation.
Inhalation; Exposure to vapors in poorly ventilated areas may cause
irritation of the nose, throat and respiratory tract.
Ingestion: Not an anticipated route of exposure. Small amounts are not anticipated to be harmful.
Chronic: No anticipated chronic effects
REGULATED CARCINOGEN STATUS
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH or OSHA listed carcinogens.
Existing Health Conditions Affected by Exposure: No known effects on other illnesses.
SECTION 4: FIRST AID PROCEDURES
If in eye: Flush immediately with water for 15 minutes Consult a physician if irritation persists.
If on skin: Wash affected area with soap and water. Launder contaminated clothing before reuse.
If vapors inhaled: Remove subject to fresh air.
If ingested: If person can swallow, give one glass of water or milk. Do not induce vomiting. Get immediate medical attention. Never give anything by mouth to an unconscious person.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point/Method: Non-flammable
Upper Explosive Limit/Lower Explosive Limit: Not applicable
Autoignition Temperature: Not applicable
Appropriate Extinguishers: Nonflammable in liquid state; use water spray. foam, dry chemical or carbon dioxide on dried product.
Special Fire Fighting Procedures: Persons exposed to products of combustion should wear self-contained breathing apparatus and full protective equipment.
Unusual Fire and Explosion Hazards: There is the possibility of pressure buildup in closed containers when heated Water spray may be used to cool the containers. Incomplete combustion can yield low molecular weight hydrocarbons, carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES
Spill or Leak Procedures: Dike if necessary contain spill with inert absorbent and transfer to containers for disposal. Keep spilled product out of sewers, watersheds or water systems.
SECTION 7: HANDLING AND STORAGE
Wear appropriate protective equipment when working with this product.
Fluid temperature extremes in storage. Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS PERSONAL PROTECTION
Eye Protection: Wear safety glasses to reduce the potential for eye contact; chemical safety goggles are appropriate if splashing or dusting is likely. Have eye washes available where eye contact can occur.
Skin Protection: Prevent prolonged or repeated contact by using rubber gloves and appropriate protective clothing. Launder contaminated clothing before reuse.
Respiratory Protection. Not normally required. Use NIOSH/MSHA approved respirator if conditions warrant.
Ventilation: General dilution ventilation.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
SECTION 10: STABILITY AND REACTIVITY DATA
Incompatibility: Not established
Hazardous Decomposition: Not established
Hazardous Polymerization: Will not occur
SECTION 11: TOXICOLOGICAL INFORMATION
No data available
SECTION 12: ECOLOGICAL INFORMATION
No data available
SECTION 13: DISPOSAL CONSIDERATIONS
To the best of our knowledge, this product does not meet the definition of hazardous waste under the U.S. EPfl Hazardous Waste Regulations 40 CFR 261. Solidify and dispose of in an approved landfill. Consult state, local or provincial authorities for more restrictive requirements.
SECTION 14: TRANSPORTATION INFORMATION
UNITED STATES DEPARTMENT OF TRANSPORTATION (DOT)
DOT Proper Shipping Name: Not Regulated
It is our opinion that the information provided here may be used to transport this product in compliance with Canadian Transportation of Dangerous Goods.
SECTION 15: REGULATORY INFORMATION
TOXIC SUBSTANCE CONTROL ACT (TSCA)
Section 4 Test Rule
This product contains a chemical substance that is subject to a Section 4 Test Rule. Contact the company TSCA Compliance Manager at 651/236-5858 for the identity of the Section 1+ chemical(s).
Section 8(b) - Inventory Status
This product is in compliance with the Toxic Substances Control Act's Inventory requirements.
Section 12(b) - Export Notice Requirements
This product contains a chemical substance that is currently on the EPAs Section 12(b) Export List. Within seven days of entering into contract to export and certainly no later than the day of export, the agent of export must notify the EPA of their intent
Contact the company TSCA Compliance Manager at 651/235-5858 for the identity of the Section 12(b) chemical(s).
SARA TITLE III
Section 313: This product does not contain regulated levels of any toxic chemical subject to the reporting requirements of section 313 or Title III of the Superfund Amendments and Reauthorization Act of 1986 (SflRfl) and 40 CFR part 372.
California Proposition 65; Proposition 65, The Safe Drinking Water and Toxic Enforcement Act of 1986:
This product does not contain known levels of any chemical known to the State of California to cause cancer or cause reproductive damage.
WHMIS IDENTIFICATION/ OTHER INTERNATIONAL REGULATIONS
SECTION 16: ADDITIONAL INFORMATION
This product contains limited amounts of residual monomer. Under normal handling and use conditions the residual monomer should not present a hazard. In storage the monomer will migrate from the emulsion and establish an equilibrium between the headspace in the storage container and the liquid emulsion Levels in excess of acceptable exposures can accumulate in non-vented headspaces above the emulsion. fill procedures appropriate for a confined space entry should be completed prior to performing any work in a bulk storage tank.
Health 1 Flammability-0 Reactivity-0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment recommendations.
Send mail to firstname.lastname@example.org regarding this web site.